GPS Odometer 125 Mileage Adjustable Overspeed Alarm for Boat Car Truck Motorcycle 85MM

Open a 85mm (3 3/8″) hole in the dashboard and allow a clearance of 55mm( 2 3/16 ) behind the panel to fit the gauge
Connection: Black wire-GND, Red-power(+), White-external button(+), Red/Yellow-Backlight, Blue-Left turn, Green-Right turn, White wire-High Beam
9-32V Working Voltage, Red and Yellow backlights available, Indication light: LEFT, HIGH BEAM, RIGHT
Securely fasten GPS antenna, preferably outdoors (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. Do not cut cable
OverSpeed Buzzer Alarm, Total Mileage Adjustable, Mileage Range: 0-999999 km Product Features:
-Suitable for all vehicles and off-road vehicles
-The signal comes directly from the satellite signal receiver(GPS Antenna), don t need other speed sensor.
-The gauge has the advantages of high precision, quick location confirmation and short start up time.
-IP67 waterproof and dustproof grade
-Reverse polarity protection and anti-fogging performance
-No Stationery Drift
-Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc.
Product Introduction
How to install it
1. Cut an 85mm (3 3/8″) hole in the panel (II) and allow a clearance of 55mm (2 3/16 ) behind the panel to fit the gauge.
2. For the GPS antenna, you should securely fasten it, black side upwards, preferably outside (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. And do not cut cable.
How to Set Odometer
1. Press the back button for 2-3 seconds first and then turn on the power supply;
2. Release the button after seeing ODO ; Press the button to change the flashing digit from 0 to 999999 to set up the target odometer value;
3. After adjustment, release button, and wait for menu to complete flashing.
4. Turn off the power supply, and turn on again. will record the setting.
How to change “BUZZ”
1. Press the button for 2-3 seconds first and then turn on the power supply;
2. Release the button after seeing BUZZ ; Press the button to change the flashing digit from 10 to 240 to set up the target overspeed buzzer alarm threshold value;
3. After adjustment, release button, and wait for menu to complete flashing.
4. Turn off the power supply, and turn on again. will record the setting.
How does GPS odometer compensation work
When the device enters tunnel/bridge without no GPS signal, the inside flash memory will record the last valid GPS longitude and latitude.
And the device will get valid GPS longitude and latitude again when leaving tunnel/bridge.
The CPU inside will calculate the two GPS data to use algorithm to add the lost odometer when in tunnel/bridge.
Technical Data
Fixing dimension
85mm(3-3/8″)
Indicating Range
0-125
Working Voltage
12V/24V
Total Mileage Range
0-999999 miles (ODO adjustable)
Trip Mileage Range
0-999.9 miles
OverSpeed Buzzer Alarm
Value Adjustable
Indication light
LEFT, HIGH BEAM, RIGHT
Backlight
Red and Yellow available
Working temperatures
– 40 to 85 C
Operation mode
LCD display, stepper motor
FAQ
ASIN NO. B07KPBYR7P
GPS keeps counting
1. After installation in the first time, GPS needs to search for signal, that’s the reason that LCD counts numbers all the time.
2. After getting signal, LCD will come back to 0. It is normal.
ASIN NO. B081PZ3HCM
How to switch Odometer & Trip Odometer
The LCD will show Total Odometer as default.
Quick press the back button to switch show Trip Odometer.
Long press the back button to reset the Trip Odometer to zero.
ASIN NO. B07KPD78JS
External button wiring
For the external button, one pin is connected to white wire of meter, the other to power negative/ground.
Package Includes:
1x GPS
1x GPS Antenna
1x Multi-plug socket
1x Installation Instruction
1x External Button